Teledyne MX300-I User Manual

Portable Oxygen Monitor Teledyne Analytical Instruments i OPERATING & SERVICE INSTRUCTIONS FOR MX300-I PORTABLE OXYGEN MONITOR 0086

Introduction MX300-I Teledyne Analytical Instruments 2 A sensor failure alarm is incorporated which warns the user if the sensor signal is lost or l

Portable Oxygen Monitor Introduction Teledyne Analytical Instruments 3 NOTE: IF THE LOW ALARM CONDITION IS TRIGGERED WITH THE OXYGEN LEVEL STAYI

Introduction MX300-I Teledyne Analytical Instruments 4  Rugged high impact ABS plastic construction  Splash resistant case  Long life class R1

Portable Oxygen Monitor Introduction Teledyne Analytical Instruments 5 The Class R17MED oxygen sensor is a disposable sensor. The sen-sor has a c

Introduction MX300-I Teledyne Analytical Instruments 6 THE MX300-I OXYGEN MONITOR, R17MED OXYGEN SEN-SOR AND ASSOCIATED HARDWARE ARE INTENDED FOR US

Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 7 Operating Instructions Notes: Upon receipt, INSPECT THE ENTIRE

Operating Instructions MX300-I Teledyne Analytical Instruments 8 Warning: The MX300-I oxygen Monitor, R17MED oxygen sensor, and associate

Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 9 Note: Do not use the plastic flow diverter with the R17MED senso

Operating Instructions MX300-I Teledyne Analytical Instruments 10 To install V-Mount Adapter, remove the battery compartment door by pry-ing up the

Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 11 3. Install 3 “AA” alkaline batteries into the holder as shown i

MX300-I Teledyne Analytical Instruments ii Copyright © 2009 Teledyne Analytical Instruments. All Rights Reserved No part of this manual may be repr

Operating Instructions MX300-I Teledyne Analytical Instruments 12 play flashing 00.0. Only the CAL and ON/OFF (I/O) keys are functional at this poi

Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 13 Note: At the end of the calibration countdown, the Monitor will

Operating Instructions MX300-I Teledyne Analytical Instruments 14 1. To set the HI alarm: Press the HI ALARM SET key once. Press the UP and DOWN

Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 15 2.1.6 Output 0-1 VDC or RS232 The MX300-I Portable Oxygen Monito

Operating Instructions MX300-I Teledyne Analytical Instruments 16 RS232 signal output has been tested with Windows Hyperterminal. The setup changes

Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 17 2.2 Operation 2.2.1 Procedure Note: Prior to every use, always t

Operating Instructions MX300-I Teledyne Analytical Instruments 18 2.3 Factors Affecting Sampling Accuracy 2.3.1 Humidity Humidity does not directly

Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 19 When a ventilator is a part of the breathing system, the alterna

Operating Instructions MX300-I Teledyne Analytical Instruments 20 Error Helium 50%, balance O2 0% Nitrous Oxide 80%, balance O2 0% Carbon Dioxi

Portable Oxygen Monitor Operating Instructions Teledyne Analytical Instruments 21 2.3.6 Cleaning The MX300-I and R17MED sensor are non-sterile dev

Portable Oxygen Monitor Teledyne Analytical Instruments iii About This Manual This Manual describes the installation, configuration, operati

Operating Instructions MX300-I Teledyne Analytical Instruments 22  Perform alarm test before each use (press the ALARM TEST key).  Use only iso

Portable Oxygen Monitor Service Instructions Teledyne Analytical Instruments 23 Service Instructions 3.1 General Service Information Without acces

Service Instructions MX300-I Teledyne Analytical Instruments 24 3.4 Sensor Maintenance DO check the sensor for damage or leaks before use. DON’T im

Portable Oxygen Monitor Service Instructions Teledyne Analytical Instruments 25 Table 3-1 Troubleshooting Symptom Why What To Do New sensor resp

Service Instructions MX300-I Teledyne Analytical Instruments 26 Symptom Why What To Do C) The sensor output has fal-len to a level where it is n

Portable Oxygen Monitor Service Instructions Teledyne Analytical Instruments 27 Symptom Why What To Do C) Calibrate. Note: In the event that n

Service Instructions MX300-I Teledyne Analytical Instruments 28 50 5 The ADC circuit failed during POST. 6 (5) 6 (There is no indication of whic

Portable Oxygen Monitor Appendix Teledyne Analytical Instruments 29 3.11 Return Authorization for Service For any service beyond sensor and batte

Appendix MX300-I Teledyne Analytical Instruments 30 Appendix A.1 Specifications Range: 0-100% oxygen Accuracy: +2% of full scale (at constant te

Portable Oxygen Monitor Appendix Teledyne Analytical Instruments 31 Left intentionally blank

MX300-I Teledyne Analytical Instruments iv Safety Messages Your safety and the safety of others are very important. Please care-fully read and unde

Appendix MX300-I Teledyne Analytical Instruments 32 A.2 Spare Parts List QTY PART NO DESCRIPTION 1 C43690-R17MED Micro-Fuel Cell R17MED with flow

Portable Oxygen Monitor Appendix Teledyne Analytical Instruments 33 Orders should be sent to: TELEDYNE Analytical Instruments 16830 Chestnut Stre

Portable Oxygen Monitor Teledyne Analytical Instruments v Table of Contents Safety Messages ...

MX300-I Teledyne Analytical Instruments vi 2.3.3 Pressure ... 182.3.4

Portable Oxygen Monitor Teledyne Analytical Instruments vii List of Figures Figure 1-1: MX300-I Front View ...

MX300-I Teledyne Analytical Instruments viii List of Tables Table 2-1: Oxygen Reading Error in a Mixture of Anesthetic Gas . 19Table 3-1 Troublesh

Portable Oxygen Monitor Introduction Teledyne Analytical Instruments 1 Introduction The Teledyne Analytical Instruments MX300-I Oxygen Monitor, h