Teledyne 200A User Manual Page 23
- Page / 225
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Teledyne API Model 200A NO
X
Analyzer Instruction Manual, 02246, Rev. G, DCN 5247
2.3 Initial Operation
1. Turn on the instrument power.
2. The display should immediately light, displaying the instrument type (M200A) and the
computer's memory configuration. If you are unfamiliar with the M200A, we recommend
that you read the overview Section 4 before proceeding. A diagram of the software menu
trees is in Table 5-5-1 and Table 5-5-2.
3. The M200A requires about 30 minutes for all internal com
ponents to come up to
temperature. During this time the ozone generator power is OFF until the membrane dryer
has time to purge itself, therefore there will be no response from the instrument, even if span
gas is coming in the sample port. During this time temperatures and other conditions are out
of specification. Because many warning conditions could be displayed warning conditions
are suppressed for 30 minutes after power up. After 30 minutes, warning messages will be
displayed until the respective warning conditions are within specifications. Use the CLR key
on the front panel to clear warning messages.
4. While waiting for instrument temperatures to come up, you can check for correct
operation by using some of the M200A's diagnostic and test features.
5. Examine the TEST functions by comparing the values listed in Table 2-2-6 to those in the
display. Rememb
er that as the instrument warms up the values may not have reached their
final values yet. If you would like to know more about the meaning and utility of each TEST
function, refer to Table 9-9-1. Also, now is a good time to verify that the instrument was
shipped with the options you ordered. Table 2-2-6 includes a list of options. Section 6 covers
setting up the options.
6. Electric Test and Optic Test both generate simulated signals in the M200A.
A. Electric Test tests the electronics of the PMT signal path. To operate Electric Test from
the front panel press SETUP-MORE-DIAG, then scroll to ELECTRICAL TEST and press
ENTR to turn on the electric test. When ELEC test is operating, scroll the TEST function
to PMT and compare instrument response to the values indicated in Table 2-2-6 . To turn
off this test press EXIT. For more information on the circuitry being tested refer to the
Troubleshooting Section 9.1.3.2.
B. Optic Test is an "end to end" test of the analyzer HVPS/PMT/ electronics/computer. It
simu
lates a signal by turning on a LED in the Sensor Module. To operate Optic Test from
the front panel press SETUP-MORE-DIAG, then scroll to OPTIC test and press ENTR to
turn on the optic test. Scroll the TEST function PMT and compare instrument response to
the values indicated in Table 2-2-6. To turn off this test press EXIT. To return to the
SAMPLE mode press EXIT until SAMPLE is displayed in the upper left display. For
more information about OT operation, see Section 9.1.3.3.
2-6
PRINTED DOCUMENTS ARE UNCONTROLLED
- TELEDYNE 1
- HIGHLIGHTS 2
- MODEL 200A 4
- NITROGEN OXIDE ANALYZER 4
- SAFETY MESSAGES 6
- TABLE OF CONTENTS 8
- LIST OF FIGURES 12
- LIST OF TABLES 13
- 1 HOW TO USE THIS MANUAL 16
- 2 GETTING STARTED 18
- 2.3 Initial Operation 23
- WARRANTY 32
- 3.3 Warranty 34
- TERMS AND CONDITIONS 35
- 4 THE M200A NO 36
- ANALYZER 36
- 4.2 Operation Summary 38
- 4.2.4 V/F Board 39
- 4.2.5 Front Panel 39
- 4.2.6 Power Supply Module 41
- 4.2.8 Ozone Generator 44
- 4.2.9 Molydbenum Converter 44
- 5 SOFTWARE FEATURES 46
- 5.1.1 Sample Menu 49
- 5.1.2 Set-Up Menu 50
- 5.2 Sample Mode 53
- 5.3 Set-Up Mode 59
- 5.3.4 Range Menu 61
- 5.3.5 Password Enable 65
- 5.3.6 Time of Day Clock 65
- 5.3.7 Diagnostic Mode 65
- 5.3.8 Communications Menu 65
- 5.3.9 Variables Menu (VARS) 66
- 5.4 Status Output 67
- 5.5 RS-232 Interface 68
- 5.5.2 Command Summary 73
- 5.5.8 Internal Variables 84
- 6.1 Rack Mount Options 86
- 6.2 Zero/Span Valves 86
- Mode No. Mode Name Action 88
- 6.5 Permeation Tube 90
- Zero/Span Valves Option 99
- NO and NO 101
- 7.6 Calibrate on NO 102
- Permeation Tube 102
- Closure 104
- 7.8.3 Data Recording Device 108
- 223 ONOONO 109
- = analyzer flow demand (cm 110
- /min (110/100) = 550 cm 111
- = 500 cm 111
- 7.8.7 Calibration Frequency 120
- 7.8.10 ZERO and SPAN Checks 123
- 7.10 Calibration Quality 128
- 7.11 References 130
- 8 MAINTENANCE 132
- Teledyne API Model 200A NO 142
- 8.9 Leak Check Procedure 146
- (table continued) 151
- 9.2 Performance Problems 173
- 9.2.1 AC Power Check 174
- 9.2.2 Flow Check 174
- 9.2.4 Negative Output 176
- 9.2.5 Excessive Noise 176
- 9.2.6 Unstable Span 177
- 9.2.7 Unstable Zero 178
- 9.2.8 Inability to Span 178
- 9.2.9 Inability to Zero 179
- 9.2.10 Non-Linear Response 180
- 9.2.11 Slow Response 181
- 9.3.2 RS-232 Communications 185
- *Required settings 191
- 9.3.4 Status/Temp Board 194
- 9.3.5 Power Supply Module 196
- C. The 200
- 9.3.6 Ozone Generator 201
- 9.3.7 Flow/Pressure Sensor 204
- 9.3.8 NO 209
- Sensor Module 209
- 9.3.10 Pneumatic System 214
- 10 M200A SPARE PARTS LIST 216
- Part No. Description 217
- Includes: Qty 220
Related products and manuals for Measuring, testing & control Teledyne 200A
(371 pages)
(42 pages)© 2020, manymanuals.com. All rights reserved. | 1.101 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals