Teledyne GFC 7001E User Manual Page 29
- Page / 321
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Specifications Model GFC7001E Carbon Dioxide Analyzer
Teledyne Analytical Instruments 29
2.3. TUV DESIGNATION
On behalf of Teledyne TÜV Rheinland Immissionsschutz und Energiesysteme GmbH has performed the
suitability test of the measuring system GFC 7001E for the component carbon monoxide.
The suitability test was carried out in compliance with the following guidelines and requirements:
EN 14626 Ambient Air Quality – Standard method for the measurement of the concentration of carbon
monoxide by nondispersive infrared spectroscopy, March 2005.
The measuring system GFC 7001E operates using the non-dispersive infrared spectroscopy.
The investigations have been carried out in the laboratory and during a field test, lasting three months. The
tested measuring ranges are:
Component Measuring Range
Carbon Monoxide CO 100 mg/m
3
EN 14626
NOTE: 0-100 ppm correlates to 0-100 µmol/mol or 0-116 mg/m
3
(at 293 K and 1013
mbar).
The minimum requirements have been fulfilled in the suitability test.
Therefore the TÜV Immissionsschutz and Energiesysteme GmbH proposes the publication as a suitability-tested
measuring system for continuous monitoring of carbon monoxide in the ambient air.
2.4. CE MARK COMPLIANCE
2.4.1. EMISSIONS COMPLIANCE
Teledyne’s GFC 7001E/EM Gas Filter Correlation CO Analyzer was tested and found to be fully compliant with:
EN61326 (1997 w/A1: 98) Class A, FCC Part 15 Subpart B section 15.107 Class A, ICES-003 Class A (ANSI
C63.4 1992) & AS/NZS 3548 (w/A1 & A2; 97) Class A.
Tested on 11-29-2001 at CKC Laboratories, Inc., Report Number CE01-249.
2.4.2. SAFETY COMPLIANCE
Teledyne’s GFC 7001E/EM Gas Filter Correlation CO Analyzer was tested and found to be fully compliant with:
IEC 61010-1:90 + A1:92 + A2:95,
Tested on 02-06-2002 at NEMKO, Report Number 2002-012219.
- MODEL GFC 7001E FAMILY 1
- CARBON MONOXIDE ANALYZERS 1
- SAFETY MESSAGES 3
- WARRANTY 5
- ABOUT THIS MANUAL 7
- TABLE OF CONTENTS 9
- ...................257 14
- LIST OF APPENDICES 16
- LIST OF FIGURES 16
- LIST OF TABLES 18
- PART I 21
- GENERAL INFORMATION 21
- INTRODUCTION 23
- 1.2.1. USING THIS MANUAL 25
- SPECIFICATIONS AND APPROVALS 27
- 2.3. TUV DESIGNATION 29
- 2.4. CE MARK COMPLIANCE 29
- GETTING STARTED 31
- ENERAL SAFETY HAZARD 36
- LECTRICAL SHOCK HAZARD 36
- Back of the instrument 37
- Sides of the instrument 37
- 3.3. ELECTRICAL CONNECTIONS 38
- A1 39
- 2 A3 A4 39
- 3.4. PNEUMATIC CONNECTIONS 42
- 3.4.1.2. Span Gas 43
- 3.4.2.1. Sample Gas Source 45
- 3.5. INITIAL OPERATION 46
- 3.5.1. STARTUP 47
- 3.5.2. WARM UP 48
- 3.5.3. WARNING MESSAGES 48
- 3.5.4. FUNCTIONAL CHECK 50
- 3.6.1. INTERFERENTS FOR CO 51
- MEASUREMENTS 51
- ANALYZERS WITHOUT OPTIONS 51
- 3.6.3. O 56
- 3.6.4. CO 56
- FREQUENTLY ASKED QUESTIONS 57
- 4.2. GLOSSARY 58
- VOLTAGE OUTPUTS 63
- 5.6.1.1. Gas Flow Rate 64
- 5.6.1.2. Valve Control 64
- 5.6.2.3. Input Gas Venting 66
- 5.6.2.4. Exhaust Outlet 66
- (OPTION 50E) 71
- 5.7. COMMUNICATION OPTIONS 73
- 5.7.3. ETHERNET (OPTION 63A) 74
- 5.8. SECOND GAS SENSORS 75
- Sensor 76
- 5.9.1. CO 77
- 5.9.2. THEORY OF OPERATION 77
- 5.11. SPECIAL FEATURES 82
- PART II 83
- OPERATING INSTRUCTIONS 83
- BASIC OPERATION 85
- 6.2. SAMPLE MODE 86
- 6.3. WARNING MESSAGES 88
- 6.4. CALIBRATION MODE 89
- 6.5. SETUP MODE 90
- INTERNAL CLOCK 95
- NALOG OUT 98
- 6.6.3. REPORTING RANGE MODES 99
- OF MEASURE 105
- FEATURE 106
- ADVANCED FEATURES 107
- 7.1.2. IDAS STRUCTURE 108
- RECORDS 111
- accepts the 126
- In all cases: 126
- discards the new 126
- FUNCTIONS 127
- OUTPUTS 129
- +DC Gnd 137
- CAUTION 139
- GENERAL SAFETY HAZARD 139
- GFC Wheel temperature 144
- 7.4.7. AIN CALIBRATION 146
- CONCENTRATION ALARMS 147
- REMOTE OPERATION 149
- Male DB-9 (RS-232) 150
- Female DB-9 (COM2) 150
- 8.1.3. COMM PORT BAUD RATE 151
- 8.1.5. COMM PORT TESTING 154
- 8.1.6. MACHINE ID 155
- 8.1.7.2. Command Syntax 157
- 8.1.7.3. Data Types 157
- 8.1.7.4. Status Reporting 158
- LED FUNCTION 164
- 8.5. MODBUS SETUP 171
- NETWORK 175
- CALIBRATION PROCEDURES 185
- 9.1. BEFORE CALIBRATION 186
- 9.1.2.2. Span Gas 187
- 9.1.2.3. Traceability 187
- CONFIGURATION 188
- INSTALLED 195
- Toggle keys to set 201
- Day, Month & Year: 201
- Format : DD-MON-YY 201
- Sequence Delta Time 203
- 9.5. CO CALIBRATION QUALITY 204
- Offset for CO REF signal 205
- Offset for CO MEAS signal 205
- 9.6.2. PRESSURE CALIBRATION 206
- 9.6.3. FLOW CALIBRATION 207
- 9.7.1. O 209
- 9.7.1.2. Set O 210
- Span Gas Concentration 210
- 9.7.1.3. Activate O 211
- Sensor Stability Function 211
- 9.7.1.4. O 212
- ZERO/SPAN CALIBRATION 212
- 9.7.2. CO 213
- 9.7.2.3. Activate CO 214
- 9.7.2.4. CO 215
- Zero/Span Calibration 215
- EPA CALIBRATION PROTOCOL 217
- 10.2. ZERO AND SPAN CHECKS 221
- 10.2.2. PRECISION CHECK 222
- 10.4. AUDITING PROCEDURE 223
- 10.5.1. LINEARITY TEST 224
- 10.6. REFERENCES 226
- PART III 227
- TECHNICAL INFORMATION 227
- THEORY OF OPERATION 229
- Measurement Cell 230
- Reference Cell 230
- CO MEAS 232
- 11.3. PNEUMATIC OPERATION 234
- 11.4. FLOW RATE CONTROL 235
- 11.4.2. PARTICULATE FILTER 236
- 11.4.3. PNEUMATIC SENSORS 236
- 11.5. ELECTRONIC OPERATION 237
- PC 104 Bus 238
- 11.5.3.2. IR Source 240
- 11.5.3.3. GFC Wheel 240
- Reference 241
- Measurement 241
- 11.5.3.4. IR Photo-Detector 242
- 11.5.4.1. Overview 242
- Detector 244
- 11.5.5. RELAY BOARD 245
- STATUS LED’s 246
- DC VOLTAGE TEST 246
- RELAY PCA 246
- PN 04135 246
- 11.5.6. MOTHERBOARD 247
- 11.5.6.4. Analog Outputs 248
- 11.5.10.2. Keyboard 252
- 11.5.10.3. Display 253
- 11.5.12. ADAPTIVE FILTER 256
- 11.5.11. SOFTWARE OPERATION 256
- 12.1. MAINTENANCE SCHEDULE 259
- AFTER WARM 262
- 12.3. MAINTENANCE PROCEDURES 264
- TROUBLESHOOTING & REPAIR 267
- (As Displayed) 271
- FUNCTION 273
- Motherboard 274
- P/N 04069 274
- D1 – M/R Sensor Status 275
- D2 – Segment Sensor Status 275
- JP4 Connector to Opto-Pickup 275
- 13.2. GAS FLOW PROBLEMS 278
- 13.2.2.1. Flow is Zero 282
- 13.2.2.2. Low Flow 282
- 13.2.2.3. High Flow 282
- 13.3. CALIBRATION PROBLEMS 283
- ELECTRICAL SHOCK HAZARD 285
- 13.4.2. EXCESSIVE NOISE 287
- 13.5. SUBSYSTEM CHECKOUT 288
- 13.5.3. I 289
- 13.5.5. RELAY BOARD 290
- 13.5.6. SENSOR ASSEMBLY 291
- 13.5.6.4. GFC Wheel Drive 292
- 13.5.6.5. IR Source 292
- (see Section 7.4.2) 294
- 13.5.7.4. Status Outputs 296
- 13.5.8. CPU 297
- 13.5.10. THE OPTIONAL CO 298
- SENSOR 298
- 13.6. REPAIR PROCEDURES 299
- SAFETY SHIELD 300
- SYNCHRONOUS MOTOR 300
- SOURCE ASSEMBLY 300
- THERMISTOR 300
- Opto-Pickup 301
- GFC WHEEL HOUSING 301
- GAIN (CO MEAS) 302
- Adjustment Made Here 303
- 13.7. TECHNICAL ASSISTANCE 304
- 14.4.1. GENERAL RULES 307
- MAINTENANCE 309
- Reporting Range, 52, 90 313
- Relay Board 317
- CANNOT DYN SPAN 319
- CANNOT DYN ZERO 319
- SYSTEM RESET 319
Related products and manuals for Carbon monoxide (CO) detectors Teledyne GFC 7001E
(30 pages)© 2020, manymanuals.com. All rights reserved. | 0.279 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals