Teledyne GFC7001T User Manual Page 134
- Page / 326
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
SetupTeledyne API – Model T300/T300M CO Analyzer
Teledyne Analytical Instruments 134
5.9.5. DARK CALIBRATION
The dark calibration test interrupts the signal path between the IR photo-detector and the
remainder of the sync/demod board circuitry. This allows the instrument to compensate
for any voltage levels inherent in the sync/demod circuitry that might affect the
calculation of CO concentration. For details see Section 9.6.1.
5.9.6. PRESSURE CALIBRATION
A sensor at the exit of the sample chamber continuously measures the pressure of the
sample gas. The data are used to compensate the final CO concentration calculation for
changes in atmospheric pressure and are stored in the CPU’s memory as the test function
PRES (also viewable via the front panel). For details see Section 9.6.2.
5.9.7. FLOW CALIBRATION
The flow calibration allows the user to adjust the values of the sample flow rates as they
are displayed on the front panel and reported through COMM ports to match the actual
flow rate measured at the sample inlet. This does not change the hardware measurement
of the flow sensors, only the software-calculated values. For details see Section 9.6.3.
5.9.8. TEST CHAN OUTPUT
When activated, output channel A4 can be used in the standard configuration to report
one of the test functions viewable from the SAMPLE mode display. (See also Section
12.5.8.2).
- Model GFC7001T 1
- Carbon Monoxide Analyzer 1
- Single Range: 3
- ABOUT THIS MANUAL 5
- IMPORTANT SAFETY INFORMATION 7
- CONSIGNES DE SÉCURITÉ 8
- TABLE OF CONTENTS 9
- 5. SETUP MENU 93 10
- LIST OF APPENDICES 15
- LIST OF FIGURES 16
- LIST OF TABLES 17
- PART I 21
- GENERAL INFORMATION 21
- 1.2. FEATURES 24
- 1.4. OPTIONS 24
- Description/Notes Reference 26
- 2.1. SPECIFICATIONS 29
- 2.3.1. SAFETY 32
- 2.3.2. EMC 32
- GETTING STARTED 33
- Back of the instrument 34
- Sides of the instrument 34
- 3.2. INSTRUMENT LAYOUT 35
- 3.2.2. REAR PANEL 39
- (Call factory for details) 40
- 3.3. CONNECTIONS AND SETUP 43
- WARNING 44
- ELECTRICAL SHOCK HAZARD 44
- A1 46
- 2 A3 A4 46
- LARM 1” RELAY 51
- LARM 4” RELAY 52
- (Figure 3-15) 54
- COM PORT DEFAULT SETTINGS 55
- RS-232 port 58
- 3.3.2. PNEUMATIC CONNECTIONS 59
- SAMPLE GAS SOURCE 61
- ALIBRATION GAS SOURCES 62
- XHAUST OUTLET 62
- AMPLE GAS SOURCE 63
- PAN GAS: 63
- ERO AIR: 63
- 10 meters long max 65
- ERO AIR 69
- CALIBRATION 72
- 3.4.3. FUNCTIONAL CHECKS 74
- 3.4.4. INITIAL CALIBRATION 75
- DILUTION RATIO SET UP 77
- ET CO SPAN GAS CONCENTRATION 78
- ZERO/SPAN CALIBRATION 79
- PART II 83
- OPERATING INSTRUCTIONS 83
- OVERVIEW OF OPERATING MODES 85
- 4.1. SAMPLE MODE 86
- READING OR DATA 87
- 4.1.2. WARNING MESSAGES 88
- operational parameters 89
- The IR source may be faulty 89
- 4.2. CALIBRATION MODE 90
- 4.3. SETUP MODE 91
- SETUP MENU 93
- CONFIGURATION 94
- NALOG OUT 95
- MODEL RANGE 96
- IMPORTANT 100
- 5.4.4. RANGE UNITS 103
- Table 5-2: Password Levels 105
- CLOCK AND ADJUSTING SPEED 108
- 5.7.2. INET (ETHERNET) 110
- MPORTANT 111
- In all cases: 112
- EXIT discards the new 112
- ENTR accepts the 112
- Front Panel Mode 113
- Indicator 113
- SECTION 113
- 5.9.1. SIGNAL I/O 115
- 5.9.2. ANALOG OUTPUT 116
- +DC Gnd 125
- CAUTION 127
- GENERAL SAFETY HAZARD 127
- (volts) 133
- 5.9.5. DARK CALIBRATION 134
- 5.9.6. PRESSURE CALIBRATION 134
- 5.9.7. FLOW CALIBRATION 134
- 5.9.8. TEST CHAN OUTPUT 134
- GFC Wheel temperature 135
- CONCENTRATION ALARMS 136
- 6.2.1. COMMUNICATION MODES 139
- 6.3. RS-232 143
- 6.4. RS-485 (OPTION) 143
- 6.5. ETHERNET 143
- IP ADDRESS) 144
- Contact your IT 145
- Network Administrator 145
- 6.7.1. MODBUS 150
- Example MODBUS Poll window: 151
- 6.7.2. HESSEN 152
- 6.7.3.5. INSTRUMENT ID 161
- LED STATE DAS STATUS 163
- 7.1. DAS STRUCTURE 164
- 7.1.2. DEFAULT DAS CHANNELS 165
- FUNCTION 168
- 7.1.4. EDITING DAS CHANNELS 169
- 7.1.8. NUMBER OF RECORDS 177
- 7.1.11. HOLDOFF FEATURE 180
- PROGRAMS 183
- REMOTE OPERATION 185
- PROGRAM 186
- 8.3. REMOTE ACCESS BY MODEM 188
- COMMUNICATIONS 191
- CALIBRATION PROCEDURES 193
- Used to calibrate optional O 194
- sensor 194
- 9.2. MANUAL CALIBRATION 195
- INSTALLED 204
- Table 9-2: AUTOCAL Modes 208
- MODE NAME ACTION 208
- SEQUENCE 211
- EXIT returns to the 213
- PRIMARY SETUP 213
- 9.5. CO CALIBRATION QUALITY 214
- ELECTRONIC SUBSYSTEMS 215
- 9.6.2. PRESSURE CALIBRATION 216
- 9.6.3. FLOW CALIBRATION 217
- 9.7.1. O 218
- SENSOR CALIBRATION 218
- 9.7.2. CO 222
- EPA CALIBRATION PROTOCOL 226
- EXPENDABLES 227
- TRACEABILITY 228
- 10.2. ZERO AND SPAN CHECKS 230
- 10.2.2. PRECISION CHECK 231
- 10.4.1. CALIBRATION AUDIT 232
- 10.4.2. DATA REDUCTION AUDIT 233
- 10.5.1. LINEARITY TEST 233
- 10.6. REFERENCES 235
- PART III 237
- TECHNICAL INFORMATION 237
- 11.1. MAINTENANCE SCHEDULE 241
- AFTER WARM 244
- 11.3. MAINTENANCE PROCEDURES 246
- GFC7001T/GFC7001TM 248
- TROUBLESHOOTING AND SERVICE 249
- As Displayed) 254
- 12.1.4. STATUS LEDS 256
- Motherboard 257
- D1 – M/R Sensor Status 258
- D2 – Segment Sensor Status 258
- JP4 Connector to Opto-Pickup 258
- RELAY PCA 259
- PN 04135 259
- 12.2. GAS FLOW PROBLEMS 261
- Sensor Option 67A 265
- 12.3. CALIBRATION PROBLEMS 266
- OX TEMPERATURE 268
- AMPLE TEMPERATURE 268
- - ELECTRICAL SHOCK HAZARD 269
- 12.4.2. EXCESSIVE NOISE 270
- 12.5. SUBSYSTEM CHECKOUT 271
- 12.5.3. I 272
- 12.5.5. LCD DISPLAY MODULE 272
- 12.5.6. RELAY BOARD 272
- 12.5.7. SENSOR ASSEMBLY 273
- Nominal Measured Frequency 274
- AC Mains Freq. TP2 TP4 274
- 50 Hz 25 300 274
- 60 Hz 30 360 274
- 12.5.8. MOTHERBOARD 276
- Section 5.9.3.9) 277
- 12.5.9. CPU 279
- 12.5.11. THE OPTIONAL CO 280
- SENSOR 280
- 12.6. REPAIR PROCEDURES 281
- SAFETY SHIELD 282
- SYNCHRONOUS MOTOR 282
- SOURCE ASSEMBLY 282
- THERMISTOR 282
- Opto-Pickup 283
- CIRCUIT GAIN (CO MEAS) 284
- Adjustment Made Here 285
- ATTENTION 286
- 12.8. TECHNICAL ASSISTANCE 288
- THEORY OF OPERATION 289
- Measurement Cell 291
- Reference Cell 291
- CO MEAS 293
- ENERAL SAFETY HAZARD 294
- 13.3. FLOW RATE CONTROL 295
- 13.3.2. PARTICULATE FILTER 296
- 13.4. ELECTRONIC OPERATION 297
- Ethernet 298
- 13.4.1. CPU 299
- ENCH TEMPERATURE 300
- HEEL TEMPERATURE 300
- EGMENT SENSOR 301
- ASSEMBLY 302
- Detector 304
- 13.4.4. RELAY BOARD 305
- 13.4.5. MOTHERBOARD 307
- O MEASURE AND REFERENCE 308
- AMPLE PRESSURE AND FLOW 308
- AMPLE TEMPERATURE SENSOR 308
- ENCH TEMPERATURE SENSOR 308
- HEEL TEMPERATURE SENSOR 308
- 13.4.6. I 309
- C DATA BUS 309
- 13.5. SOFTWARE OPERATION 313
- 14.4.1. GENERAL RULES 318
- AND MAINTENANCE 319
- GLOSSARY 323
Related products and manuals for Oxygen Equipment Teledyne GFC7001T
Oxygen Equipment Teledyne OT-3 User Manual
(50 pages)
(50 pages)
Oxygen Equipment Teledyne 3000TA User Manual
(19 pages)
(19 pages)
Oxygen Equipment Teledyne 2230R User Manual
(26 pages)
(26 pages)
Oxygen Equipment Teledyne 2150EX User Manual
(115 pages)
(115 pages)
© 2020, manymanuals.com. All rights reserved. | 0.422 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals